Search found 8 matches
- Tue Jan 05, 2016 12:40 am
- Forum: Questions & Comments
- Topic: Transom and temp front frame
- Replies: 1
- Views: 13379
Transom and temp front frame
Matt, Where or how do I find accurate transom and temp frames dimensions? Kinda thought the main frame would suffice but seems the profile and dimensions differ. Transom I could pencil out after the hull is stitched and glassed. But the main temp frame and the small frame frame (I dont have drawings...
- Sun Jan 03, 2016 6:31 pm
- Forum: Questions & Comments
- Topic: Cleat location and Front temp frame SABALO 15'
- Replies: 3
- Views: 15019
Re: Cleat location and Front temp frame SABALO 15'
Matt, Where do I find the large and small TEMP FRONT Frame dimensions and transom dimensions??? All other parts are ready for assembly...just the two temp frames and transom need to be sketched out and cut. Please advise how to proceed. I am in Manila today to buy epoxy. Internet on the island is al...
- Sat Dec 12, 2015 1:48 am
- Forum: Stitch and Glue Tutorial
- Topic: Spacers, stitching Sabalo 15
- Replies: 1
- Views: 45971
Spacers, stitching Sabalo 15
Matt, Easy questions. 1. Are spacers inserted between each stitch to ensure uniform space along the entire length of panel, floor deck, whatever to be glued with epoxy...or are spacers only used where there is a hard-spot? 2. What is the recommended procedure--- a light contact (just touching)- of p...
- Fri Dec 11, 2015 3:49 am
- Forum: Questions & Comments
- Topic: Cleat location and Front temp frame SABALO 15'
- Replies: 3
- Views: 15019
Cleat location and Front temp frame SABALO 15'
Matt, 1. Page 13 of 38 refers --- top of page 13...point 2 at top of page --- FORWARD TANK WELL cleat location?? ---Quote..refer to the T-cleat location drawing. Glue the cleats below the lines shown...unquote--On which page is the cleat location detailed?? 2. Page 11 of 38 refers---the page shows a...
- Mon Nov 09, 2015 1:34 am
- Forum: Questions & Comments
- Topic: Zip ties or wire and rudder cable
- Replies: 6
- Views: 16379
Re: Zip ties or wire and rudder cable
Matt,
Thanks for the advice. I'll try to locate an armature winder and buy copper wire before setting off to the island. Can you please recommend a suitable wire gauge and possibly a back-up gauge too. More often than not...stocks are depleted!
Thanks
Ian S.
Thanks for the advice. I'll try to locate an armature winder and buy copper wire before setting off to the island. Can you please recommend a suitable wire gauge and possibly a back-up gauge too. More often than not...stocks are depleted!
Thanks
Ian S.
- Sun Nov 08, 2015 7:18 am
- Forum: Questions & Comments
- Topic: Zip ties or wire and rudder cable
- Replies: 6
- Views: 16379
Re: Zip ties or wire and rudder cable
Onkabob, Thanks for the reply and sound advice. I did go longer 4" and chose 3mm width figuring that thinner would break quicker and this comes from past experience rebuilding a Suzuki cruiser here in China. Those zip ties were 5mm wide and some snapped when tensioned. And, I gone to 1000 in to...
- Fri Nov 06, 2015 10:45 pm
- Forum: Questions & Comments
- Topic: Rudder cable routing
- Replies: 1
- Views: 12238
Rudder cable routing
Right, so thru hull cable routing for a rudder is a no-no and after consideration maybe not a good idea. Is there anyone out there in the distant blue yonder that can suggest or detail a proven way to route rudder cable and what route or suggest a path to follow?
- Tue Nov 03, 2015 7:34 am
- Forum: Questions & Comments
- Topic: Zip ties or wire and rudder cable
- Replies: 6
- Views: 16379
Zip ties or wire and rudder cable
Matt, Done some serious reading re stitching. What is your recommendation - zip ties or copper wire? Do you have a recommended width x length for zip ties and approximately what number of ties at 4" spacings would I need for a Sabalo? Please bear in mind I have to carry all ancillary fittings t...