12' Garvey flex

Boatplans.dk · Post by **Boatplans.dk** » Sun Jan 09, 2005 3:48 am

Hello Builders,

The plans for the new 12’ dingy is ready for purchase. It is called 12’ Garvey flex so it became a new boat in the Garvey flex series. The plans are set at a introduction price for a short period. Hope you will enjoy the new design. The full description of the 12’ Garvey flex can be seen here www.boatplans.dk/mo-gf12.asp

I am looking for someone to build the first boat. For the project I will supply the plans, epoxy, fibre glass and filler needed for the building and in return you will have to sent me pictures of the building and the finished boat. If you are interested in participating in this project, please sent me an email with a introduction and some references.

dorymate · Post by **dorymate** » Wed Jan 12, 2005 10:44 am

Plans look great, should be a good build and a versatile boat.Thanks again.

Post by **jem** » Mon Jan 17, 2005 12:00 pm

Hey Builders,

Pass the word about this one. Here's what Morten is looking to do:

He will send you the plans at NO CHARGE.

You loft and cut out the panels and send him pictures.

He will then send you the epoxy, fiberglass, and woodflour at NO CHARGE. you get them for free!

Then you build and send him pictures. The only thing you pay for is plywood, the motor, and the paint and you have yourself a nice boat. He gets the benefits of having pictures of the boat built. That's a great deal!

Skylane182 · Post by **Skylane182** » Sat Jan 22, 2005 9:28 am

Did you find a builder yet? I have a gamefisher 9.9hp that needs a home,,,If I can talk the "boss" (wife) into another project?...hee hee

Post by **jem** » Sat Jan 22, 2005 10:12 am

Skylane182 wrote:Did you find a builder yet? I have a gamefisher 9.9hp that needs a home,,,If I can talk the "boss" (wife) into another project?...hee hee

Send Morten an e-mail! Will only cost you plywood, paint, and some time.

Boatplans.dk · Post by **Boatplans.dk** » Tue Mar 01, 2005 1:44 am

I have found a test builder for the 12' Garvey flex. Thanks to all of you that applied for the job.

banoe · Post by **banoe** » Thu Mar 03, 2005 11:50 pm

Morten, Can you stretch the Garvey flex. to 15'? I got a 20hp long shaft out board in the shed that needs a home.

Boatplans.dk · Post by **Boatplans.dk** » Fri Mar 04, 2005 12:02 am

Something like this?

It is 14' but relatively wider than the 12'. It will cary a 20 hp outboard.

Guest · Post by **Guest** » Tue Mar 08, 2005 9:45 pm

Morten some questions

Could you remove center seats and put in plywood floor with ribs?
Make the front seat larger for standing and fishing?
How wide is the boat.
How much plywood and epoxie would it use.

Boatplans.dk · Post by **Boatplans.dk** » Tue Mar 08, 2005 11:29 pm

The boat can be build with 9 sheets of plywood. I haven’t calculated the amount of epoxy yet.

The boat is 1,622 m or 5’4”.

It would be possible to extend the forward seat abaft. Then leave out the two seats at the centre and then having a floor instead. The frames will still be needed. It will just demand more plywood and epoxy.

JEM Watercraft

12' Garvey flex

12' Garvey flex

garvey flex build

builder yet?

Re: builder yet?

Test builder