Orbital sander?
-
- Posts: 374
- Joined: Wed Mar 30, 2011 7:20 am
- Type of boat I like: Fishing SOTs.
- Location: Adelaide, South Australia.
Orbital sander?
Hi all. I will be needing an orbital sander for my upcoming build. I don't have too much coin so I would appreciate a bit of advice on what would be the minimum quality I would need. I see Hitachi orbital sanders for around AU$120. Are these any good?
My psychologist reckons I need lots of fishin' therapy!
-
- Site Admin
- Posts: 4915
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: Orbital sander?
Hitachi makes some good quality. I used a Dewalt and it gets the job done.
-Matt. Designer.
-
- Posts: 401
- Joined: Fri Jul 18, 2008 10:12 am
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: Seaford, South Oz
Re: Orbital sander?
I bought a cheap one (Ozito) a while back and while it does the job ok on timber I find I can't use it to smooth glassed areas because it is too vicious. I think the important thing is to get a variable speed ROS - mine isn't and I regret not spending the extra. The other thing with Ozito is that the velcro pad is rubbish - I only recently discovered that this is a common problem and am contemplating trying to get some sort of warranty recompense.
As for Hitachi, I'm not familiar with their sanders but I recently bought a Hitachi jigsaw and it is very good. I perceive them as a quality brand.
As a final comment, you really don't need a ROS to build a S&G boat - but it will probably be handy for other stuff and it's always nice to have an excuse to buy new toys .
As for Hitachi, I'm not familiar with their sanders but I recently bought a Hitachi jigsaw and it is very good. I perceive them as a quality brand.
As a final comment, you really don't need a ROS to build a S&G boat - but it will probably be handy for other stuff and it's always nice to have an excuse to buy new toys .
Cheers, Bob
Laker 13 - christened and slimed (just).
Laker accessories underway.
Laker 13 - christened and slimed (just).
Laker accessories underway.
-
- Posts: 374
- Joined: Wed Mar 30, 2011 7:20 am
- Type of boat I like: Fishing SOTs.
- Location: Adelaide, South Australia.
Re: Orbital sander?
I'm not itching to spend money on tools I don't really need, but someone told me that it was pretty essential, that there was to much sanding to do it by hand. I don't know, that's why I am hammering this forum!
My psychologist reckons I need lots of fishin' therapy!
-
- Site Admin
- Posts: 4915
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: Orbital sander?
Careful application of epoxy will save LOTS of sanding. Use just enough epoxy to get the task done. Not a drop more. Prep your work to an extreme degree. Plenty of masking tape. Work neat and clean up runs and drips while they are still in a liquid state.
-Matt. Designer.
-
- Posts: 374
- Joined: Wed Mar 30, 2011 7:20 am
- Type of boat I like: Fishing SOTs.
- Location: Adelaide, South Australia.
Re: Orbital sander?
So you are saying that if I do that the sanding will be not too much?
I think my little outrigger build project will come in handy to hone some skills and ultimately make life a bit easier.
I think my little outrigger build project will come in handy to hone some skills and ultimately make life a bit easier.
My psychologist reckons I need lots of fishin' therapy!
-
- Site Admin
- Posts: 4915
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: Orbital sander?
You'll still have to do some sanding.
But not nearly as much if you are sloppy with the epoxy and glob it on haphazardly. You'll be cleaning up minor surface imprefections versus trying to level out uneven application.
But not nearly as much if you are sloppy with the epoxy and glob it on haphazardly. You'll be cleaning up minor surface imprefections versus trying to level out uneven application.
-Matt. Designer.
-
- Posts: 374
- Joined: Wed Mar 30, 2011 7:20 am
- Type of boat I like: Fishing SOTs.
- Location: Adelaide, South Australia.
Re: Orbital sander?
Ok, that clarifies it. I think I'll proceed without the sander and only buy one if it seems that it is needed either because my arms give out or if I'm more sloppy than I think I will be. Thanks!
My psychologist reckons I need lots of fishin' therapy!
-
- Posts: 68
- Joined: Thu Oct 28, 2010 4:01 am
- Type of boat I like: 18-36 Trapper
- Location: Northern Territory, Australia
Re: Orbital sander?
Get a sander Mate. You're gonna want it.....Hitachi, Bosch, Makita are all good. Try the second hand joints if you don't want to outlay for a new one. If you are anything like the rest of the inmates on this forum, you'll be looking at your next build before this one is done.
-
- Posts: 374
- Joined: Wed Mar 30, 2011 7:20 am
- Type of boat I like: Fishing SOTs.
- Location: Adelaide, South Australia.
Re: Orbital sander?
Hahaha you make it sound like a sentence. You might be right. I will check out a few second hand places, I have picked up some real bargains from them at times, as well as some real s@#t, but it's worth a look. I've already planned on buying a jigsaw, that's a no brainer.Whirly wrote:Get a sander Mate. You're gonna want it.....Hitachi, Bosch, Makita are all good. Try the second hand joints if you don't want to outlay for a new one. If you are anything like the rest of the inmates on this forum, you'll be looking at your next build before this one is done.
My psychologist reckons I need lots of fishin' therapy!