JEM Watercraft

JEM Watercraft

Customer Service Forum
Direct Links To: Canoe Plans  --  Kayak Plans  --  Other Plans
 
It is currently Fri Dec 15, 2017 7:16 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 9 posts ] 
Author Message
 Post subject: stripped Freedom 15 as a SOT?
PostPosted: Sun Apr 15, 2012 10:52 am 
Offline

Joined: Tue Jan 24, 2012 10:04 am
Posts: 30
Hi Matt
Through some delays, I am finally finishing my Sabalo 15. After 40 years f using power tools with no accidents, I let a trim router kick back and run a 1/2" top bearing pattern bit up my left thumb. It hit just above my thumb nail and went all the way up above the top knuckle leaving a 1/2 inch of hamburger in its wake. Fortunately the tendons were only knicked and after 3 hours the surgeon was able to stitch it back together. It is completely healed now and looks remarkably better than I would have believed. My father always told me " If ya know better, do better and things will work better" I knew better and it didn't turn out well. Next, I want to either do another Sabalo 15 as an ss&g or put a SOT cockpit in a Stripped Freedom 15. I have studied the hull shapes and I think the Freedom may actually have more flat hull in the water than the Sabalo. What do you think? I believe a stripped SOT would get alot of attention in my area. I have not decided if I would want a tank well or not. Maybe a tank well option would be a good idea.
I would appreciate the opinions of Matt and any Freedom15 owners.
Thanks
Jesse


Top
 Profile  
 
 Post subject: Re: stripped Freedom 15 as a SOT?
PostPosted: Sun Apr 15, 2012 2:20 pm 
Offline
Site Admin
User avatar

Joined: Fri Jun 18, 2004 8:14 pm
Posts: 4855
Location: Greensboro, NC
If a 325 max payload and 27.5" beam by 15'6 long is acceptable, I could send you plans for a strip Wadefish SOT tomorrow. It's one of my drawing board projects that the prototype builder didn't get started on.

If you need bigger, then it's a custom project.

_________________
-Matt. Designer.


Top
 Profile  
 
 Post subject: Re: stripped Freedom 15 as a SOT?
PostPosted: Sun Apr 15, 2012 9:55 pm 
Offline

Joined: Tue Jan 24, 2012 10:04 am
Posts: 30
Hey Matt
Do you have any preview drawings of the stripped Wadefish that you could post? Like the ones you post for your other designs. I would like to compare the Wadefish with the Freedom as far as bottom shape is concerned. I like the smooth flowing lines of the Freedom. I think it would be a very quiet hull with minimum slap noises from waves. Sneeking up on tailing Redfish requires stealth in shallow water.
Both boats are about the same size dimensionally.


Top
 Profile  
 
 Post subject: Re: stripped Freedom 15 as a SOT?
PostPosted: Mon Apr 16, 2012 6:29 am 
Offline
Site Admin
User avatar

Joined: Fri Jun 18, 2004 8:14 pm
Posts: 4855
Location: Greensboro, NC
I'll post them later this evening.

_________________
-Matt. Designer.


Top
 Profile  
 
 Post subject: Re: stripped Freedom 15 as a SOT?
PostPosted: Tue Apr 17, 2012 6:39 am 
Offline
Site Admin
User avatar

Joined: Fri Jun 18, 2004 8:14 pm
Posts: 4855
Location: Greensboro, NC
having some issues uploading pictures. I posted them off our facebook page:

http://www.facebook.com/media/set/?set= ... 106&type=3

Image

Image

Image

_________________
-Matt. Designer.


Top
 Profile  
 
 Post subject: Re: stripped Freedom 15 as a SOT?
PostPosted: Tue Apr 17, 2012 7:58 am 
Offline
Site Admin
User avatar

Joined: Fri Jun 18, 2004 8:14 pm
Posts: 4855
Location: Greensboro, NC
The name of the game with SOTs is matching the displacement of the hull at a given depth with the subfloor height.

The original customer wanted a narrow touring kayak. Problem with that is a narrow hull is less stable by nature. Make it a SOT with the paddlers entire body being raise 3-4 inches, it becomes even less stable.

So to get max displacement without it being completely flat, I used flat panel sections with rounded chines. There is also constantl flare going up the hull until about 1/2 the height.

It should feel stable to an experienced paddler with moderate balancing ability.

_________________
-Matt. Designer.


Top
 Profile  
 
 Post subject: Re: stripped Freedom 15 as a SOT?
PostPosted: Tue Apr 17, 2012 10:12 pm 
Offline

Joined: Tue Jan 24, 2012 10:04 am
Posts: 30
I have not built a stripped boat, yet. Do you think the small radius of those chines will be difficult to get strips to conform? I think narrower than normal strips thru the chines would be easier. What is the price for these plans? I may try it for the challenge. I would rather it had been the wider Wadefish stripped.
Thanks for posting these drawings.
Jesse


Top
 Profile  
 
 Post subject: Re: stripped Freedom 15 as a SOT?
PostPosted: Wed Apr 18, 2012 6:25 am 
Offline
Site Admin
User avatar

Joined: Fri Jun 18, 2004 8:14 pm
Posts: 4855
Location: Greensboro, NC
The tighter curves will be a little harder to strip out. But as you said, narrower strips in that area would be better.

That's the only strip SOT I currently have complete. The go wider, I'd have to start from scratch.

_________________
-Matt. Designer.


Top
 Profile  
 
 Post subject: Re: stripped Freedom 15 as a SOT?
PostPosted: Wed Apr 18, 2012 7:24 am 
Offline

Joined: Wed Nov 03, 2010 7:12 am
Posts: 125
Location: KC.MO.
You could always assemble the wadefish with stripped pannels...


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Bing [Bot] and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Template made by DEVPPL/ThatBigForum