Matt,
on page 15 of the 37 page instructions, it says Check to ensure the bow/stern jig is vertical.
But a bow/stern jig is not mentioned or pictured anywhere else in the instructions/plans for the Trapper 15-38.
Of course I could check that the bows themselves are vertical at that point,
but I'm wondering about the jig, am I missing something that would help the build come out better?
Thanks
Les
Trapper 15.38 bow/stern jig.
-
- Posts: 197
- Joined: Mon Sep 12, 2011 6:29 pm
- Type of boat I like: JEM Trapper by Matt
- Location: Chicago
- Contact:
Trapper 15.38 bow/stern jig.
Les Richard Forgue
-
- Site Admin
- Posts: 4915
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: Trapper 15.38 bow/stern jig.
Should have this in the plansLesForgue wrote:Matt,
on page 15 of the 37 page instructions, it says Check to ensure the bow/stern jig is vertical.
But a bow/stern jig is not mentioned or pictured anywhere else in the instructions/plans for the Trapper 15-38.
Of course I could check that the bows themselves are vertical at that point,
but I'm wondering about the jig, am I missing something that would help the build come out better?
Thanks
Les
-Matt. Designer.
-
- Posts: 197
- Joined: Mon Sep 12, 2011 6:29 pm
- Type of boat I like: JEM Trapper by Matt
- Location: Chicago
- Contact:
Re: Trapper 15.38 bow/stern jig.
Hi Matt,
I do not have that image on any of the instruction or plan pages.
Can you email me a picture of that bow alignment jig drawing,
showing dimensions, and with a little instruction on how to use it? les.forgue@fisglobal.com
What I do have is:
Pages 1 thru 37 of Trapper Build Instructions Rev00 - 02/15/09.
Thirteen 11x17 Trapper 15-38 Plans pages =
- Rev 00 - 02/24/09 Reference
- Rev 00 - 02/24/09 Nesting
- Rev 00 - 02/24/09 Sheet 1.1
- Rev 00 - 02/24/09 Sheet 1.2
- Rev 00 - 02/24/09 Sheet 3
- Full Scale pattern end of panel 1
- Full Scale pattern end of panels 2 & 3
- Full Scale pattern end of panel 4 Left, showing actual end
- Full Scale pattern end of panel 4 Right, showing approach to end
- Rev 00 - 02/24/09 Frames
- Rev 00 - 02/24/09 QA 1
- Rev 00 - 02/24/09 QA 2
- Rev 00 - 02/24/09 Frame REF
THANKS!
I do not have that image on any of the instruction or plan pages.
Can you email me a picture of that bow alignment jig drawing,
showing dimensions, and with a little instruction on how to use it? les.forgue@fisglobal.com
What I do have is:
Pages 1 thru 37 of Trapper Build Instructions Rev00 - 02/15/09.
Thirteen 11x17 Trapper 15-38 Plans pages =
- Rev 00 - 02/24/09 Reference
- Rev 00 - 02/24/09 Nesting
- Rev 00 - 02/24/09 Sheet 1.1
- Rev 00 - 02/24/09 Sheet 1.2
- Rev 00 - 02/24/09 Sheet 3
- Full Scale pattern end of panel 1
- Full Scale pattern end of panels 2 & 3
- Full Scale pattern end of panel 4 Left, showing actual end
- Full Scale pattern end of panel 4 Right, showing approach to end
- Rev 00 - 02/24/09 Frames
- Rev 00 - 02/24/09 QA 1
- Rev 00 - 02/24/09 QA 2
- Rev 00 - 02/24/09 Frame REF
THANKS!
Les Richard Forgue