JEM Watercraft

JEM Watercraft

Customer Service Forum
Direct Links To: Canoe Plans  --  Kayak Plans  --  Other Plans
 
It is currently Sat Oct 21, 2017 10:32 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 4 posts ] 
Author Message
 Post subject: Cleat location and Front temp frame SABALO 15'
PostPosted: Fri Dec 11, 2015 3:49 am 
Offline

Joined: Tue Oct 27, 2015 11:59 pm
Posts: 8
Matt,

1. Page 13 of 38 refers --- top of page 13...point 2 at top of page --- FORWARD TANK WELL cleat location?? ---Quote..refer to the T-cleat location drawing. Glue the cleats below the lines shown...unquote--On which page is the cleat location detailed??

2. Page 11 of 38 refers---the page shows a graphic of the FRONT TEMP FRAME...this is understood as a lineup for hull panels...on 19 point 13 and 14 the assembly mentions stitch panels C and B.....understood and the TEMP FRAME is still there to assist in alignment----page 35 refers point 29---stitch panel A to frames---TEMP FRAME STILL IN PLACE as per drawing. Page 36 ---point 30-install floors---and the sketch still shows the TEMP FRAME in place and from there forward there is no mention of removing the FRONT TEMP FRAME. Could please clarify Matt...does this TEMP FRAME remain and become an integral part of the construction or at which point of overall assembly is the TEMP FRONT FRAME REMOVED??

JIG for drilling stitch holes. Page 15 mentions 12" spaced holes for Sabolo Kayak and then on page 17 it is mentioned 6-8" holes...----Which spacing is is recommended.????---- My gut feeling is 6" for more accuracy during panel alignment.

Thats it.....Thanks Matt.

Ian S.


Top
 Profile  
 
 Post subject: Re: Cleat location and Front temp frame SABALO 15'
PostPosted: Fri Dec 11, 2015 6:24 pm 
Offline
Site Admin
User avatar

Joined: Fri Jun 18, 2004 8:14 pm
Posts: 4855
Location: Greensboro, NC
1) Sheet 4.1

2) temp frame should come out unless you doing something custom with it.

If you're using 3mm ply, 6". You could just do 6" regardless but if using 4mm, 8" should be ok. You can always add more.

_________________
-Matt. Designer.


Top
 Profile  
 
 Post subject: Re: Cleat location and Front temp frame SABALO 15'
PostPosted: Sun Jan 03, 2016 6:31 pm 
Offline

Joined: Tue Oct 27, 2015 11:59 pm
Posts: 8
Matt,

Where do I find the large and small TEMP FRONT Frame dimensions and transom dimensions??? All other parts are ready for assembly...just the two temp frames and transom need to be sketched out and cut. Please advise how to proceed.

I am in Manila today to buy epoxy. Internet on the island is almost impossible and will check in to website tomorrow for a reply before stetting sail back to island.

Thanks,

Ian S


Top
 Profile  
 
 Post subject: Re: Cleat location and Front temp frame SABALO 15'
PostPosted: Wed Jan 06, 2016 6:58 am 
Offline
Site Admin
User avatar

Joined: Fri Jun 18, 2004 8:14 pm
Posts: 4855
Location: Greensboro, NC
IanS wrote:
Matt,

Where do I find the large and small TEMP FRONT Frame dimensions and transom dimensions??? All other parts are ready for assembly...just the two temp frames and transom need to be sketched out and cut. Please advise how to proceed.

I am in Manila today to buy epoxy. Internet on the island is almost impossible and will check in to website tomorrow for a reply before stetting sail back to island.

Thanks,

Ian S


Should be in the drawing packet. Drawing named "misc".

_________________
-Matt. Designer.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Template made by DEVPPL/ThatBigForum