JEM Watercraft

JEM Watercraft

Customer Service Forum
Direct Links To: Canoe Plans  --  Kayak Plans  --  Other Plans
 
It is currently Mon Dec 11, 2017 10:58 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 4 posts ] 
Author Message
 Post subject: My TouringPirogue-TV Build
PostPosted: Sat Nov 12, 2016 9:02 pm 
Offline

Joined: Sun Nov 06, 2016 7:32 pm
Posts: 2
Hello, New member here not quite a newbie but built a typical Uncle Johns about 11 years ago. Glassed the inside n out and still use it regularly. Refinished it last year and added copper sheeting at the ends mostly to protect the underside luan at the points. This past summer I participated in a number of paddling events and notice how well kayaks moved through the water. However the setting position is too low and I prefer a more open access so that I can keep my feet dry will boarding. Now the new build. I kicked around quite a bit on building it as a stripper but leaning towards another plywood boat. I was looking into what Owl Hardwoods offered in Chicago. They have Baltic Birch in 4 x 8 sheets in both 1/8 and 1/4. I would like opinions on a lighter version using 1/8 or a combination of 1/8 sides and 1/4 floor. Opinions of the Baltic Birch or Okoume or any sheeting. I know I mentioned light weight but will glass it most likely all over the outside for strength and protection. I am undecided about the inside. I see different butt joints, pros and cons? Thank you Ken Almost forgot. I would like to leave out the forward thwart so as I do not need to step over. I thought about running a front cover back a little to give it some strength. Opinions? Thank you


Top
 Profile  
 
 Post subject: Re: My TouringPirogue-TV Build
PostPosted: Sat Nov 12, 2016 9:42 pm 
Offline
Design Reviewer
User avatar

Joined: Sat Jun 19, 2004 11:08 am
Posts: 1271
Location: Somewhere around Central Florida
Everyone does a build the way they want it and like it. That's the beauty of doing it yourself. :D
Myself I like the 1/8 in wood with it epoxy saturated and glassed all the way around. Butt Joints are my favorite and I glass over the joint ( Both sides ) with 3.5 oz tight woven glass. The piece of glass is extended about 2 inches on each side of the seam covering the seam.
When the boat can be glassed I do it in the 3.5 oz tight woven.

Chuck.

_________________
Remember:
Amateurs built the Ark...... Professionals built the Titanic
Visit some fine paddlers at The Southern Paddler


Top
 Profile  
 
 Post subject: Re: My TouringPirogue-TV Build
PostPosted: Sun Nov 13, 2016 5:44 pm 
Offline
Site Admin
User avatar

Joined: Fri Jun 18, 2004 8:14 pm
Posts: 4855
Location: Greensboro, NC
Birch isn't very rot resistant.

But if you're encasing inside and out with fiberglass, then not much of an issue so long as you keep on top of any scrapes getting through fiberglass layer.

Be careful about 4 x8 birch. It usually isn't Baltic birch which has no voids and even thickness plies.

_________________
-Matt. Designer.


Top
 Profile  
 
 Post subject: Re: My TouringPirogue-TV Build
PostPosted: Sun Nov 13, 2016 10:35 pm 
Offline

Joined: Sun Nov 06, 2016 7:32 pm
Posts: 2
Thank you both for the replies. I was mistaken, Owl Hardwood does not have 1/8 Baltic Birch in 4 x 8. However they do have Meranti, Okoume. I stopped at Menards today. They have 1/4 Baltic Birch but only 1/8 was there basic luan. Maybe Home Depot may have something.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Bing [Bot] and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Template made by DEVPPL/ThatBigForum