JEM Watercraft

JEM Watercraft

Customer Service Forum
Direct Links To: Canoe Plans  --  Kayak Plans  --  Other Plans
 
It is currently Fri Oct 20, 2017 7:31 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 30 posts ]  Go to page Previous  1, 2, 3  Next
Author Message
 Post subject: Re: starting a TV 15-32 in SC
PostPosted: Thu May 08, 2014 12:34 pm 
Offline

Joined: Tue Nov 03, 2009 2:29 pm
Posts: 179
Location: Longview East Texas
I went with 1"* 1/4" outer rub rail and same inside gunnel with spacers between, made bulkhead and sub frames then formed deck (made flat panel on bench) [url][URL=http://s469.photobucket.com/user/makenmend/media/TV%2015-29/totolaker12andoutriggersprogress9_resize-1.jpg.html]Image[/url][/url]


Top
 Profile  
 
 Post subject: Re: starting a TV 15-32 in SC
PostPosted: Thu May 08, 2014 12:45 pm 
Offline

Joined: Tue Nov 03, 2009 2:29 pm
Posts: 179
Location: Longview East Texas
the deck glassed on bottom side[url][URL=http://s469.photobucket.com/user/makenmend/media/TV%2015-29/c5b95a1f-acf8-4ab6-a0ef-88cb08d01540.jpg.html]Image[/url][/url]then goopied on and glassed top side over lapping the rub rail.[url][URL=http://s469.photobucket.com/user/makenmend/media/TV%2015-29/totolaker12andoutriggersprogress.jpg.html]Image[/url][/url]

[url][URL=http://s469.photobucket.com/user/makenmend/media/TV%2015-29/TVToto16_resize-1.jpg.html]Image[/url][/url]


Top
 Profile  
 
 Post subject: Re: starting a TV 15-32 in SC
PostPosted: Thu May 08, 2014 1:08 pm 
Offline

Joined: Wed Mar 19, 2014 6:40 pm
Posts: 23
Makenmend - that's a pretty stripper right there! :lol:
So you used 1" x 1/4"? Just glued on and no hardware? I plan on doing cedar strips for decks too but I would like to skip on those internal frames if possible... thanks


Top
 Profile  
 
 Post subject: Re: starting a TV 15-32 in SC
PostPosted: Fri May 09, 2014 11:09 am 
Offline

Joined: Tue Nov 03, 2009 2:29 pm
Posts: 179
Location: Longview East Texas
skipping on the sub frames is nice until someone thinks it's a good place to sit ! 1st hand experience here !!
I'm about to make a 15-32 for a good friend, panels for bottom and sides are cut, scarfed and drilled, ready for when my friend visits memorial week end, so he can stitch it up and go 3d.
Bottom 3/8'',side 1/4'' marine ply the rest will be stripped, assembling the tumble home panels now.
[url][/url]
Image

MM


Top
 Profile  
 
 Post subject: Re: starting a TV 15-32 in SC
PostPosted: Mon May 12, 2014 8:52 am 
Offline

Joined: Wed Mar 19, 2014 6:40 pm
Posts: 23
second wet out of glass
Image
using scraps quite a bit in this boat
Image
put 1/2 " 45 deg pvc elbow in bow and stern for lines
Image
deck trial
Image


Top
 Profile  
 
 Post subject: Re: starting a TV 15-32 in SC
PostPosted: Mon May 19, 2014 8:45 am 
Offline

Joined: Wed Mar 19, 2014 6:40 pm
Posts: 23
Image
a little bow heavy in this pic
Image

I ran the inner pieces of cypress up to bow and stern and raised them gradually at each end so I can sand down and have a shelf to glue the decks to. make sense? Because of the tumblehome you have to bring them higher for flat deck going from side to side.


Top
 Profile  
 
 Post subject: Re: starting a TV 15-32 in SC
PostPosted: Tue May 20, 2014 11:54 am 
Offline

Joined: Wed Mar 19, 2014 6:40 pm
Posts: 23
Image

now for some more fitting...

And I ordered some, shhh, paint. I know varnish seems to be the norm here but this one is going to be camo. :wink:


Top
 Profile  
 
 Post subject: Re: starting a TV 15-32 in SC
PostPosted: Tue May 20, 2014 11:06 pm 
Offline

Joined: Fri Jul 18, 2008 10:12 am
Posts: 388
Location: Seaford, South Oz
grayduck wrote:
And I ordered some, shhh, paint. I know varnish seems to be the norm here but this one is going to be camo. :wink:


OK, but don't blame us when you can't find it............ :lol:

_________________
Cheers, Bob

Laker 13 - christened and slimed (just).
Laker accessories underway.


Top
 Profile  
 
 Post subject: Re: starting a TV 15-32 in SC
PostPosted: Wed May 28, 2014 1:47 pm 
Offline

Joined: Wed Mar 19, 2014 6:40 pm
Posts: 23
Bob, that's funny. Maybe that should be my goal...

All the clamps I own
Image

And now time for sanding, filling, fairing and some fill the weave coats...


Top
 Profile  
 
 Post subject: Re: starting a TV 15-32 in SC
PostPosted: Tue Jun 03, 2014 12:21 pm 
Offline

Joined: Wed Mar 19, 2014 6:40 pm
Posts: 23
rails done
Image

Image


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 30 posts ]  Go to page Previous  1, 2, 3  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Bing [Bot] and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Template made by DEVPPL/ThatBigForum