The drive is held down by a couple of twist-out knobs and is easily removable while on the water. So you can launch, paddle, or pole in real shallow water.Wannabe wrote:Matt,
That is what I was looking for. Might be tricky launching off a cement boat ramp unless they fold up or something. Sounds expensive.
Bob
Native Ultimate Plans
-
- Site Admin
- Posts: 4915
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: Native Ultimate Plans
-Matt. Designer.
-
- Posts: 20
- Joined: Sun Jan 15, 2006 11:06 am
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: Little Rock, Arkansas
- Contact:
Re: Native Ultimate Plans
Those fins can also be pulled up against the bottom of the boat. I would guess they would only hang down another 2" or so below the lowest part of the boat.
Kris
Kris
-
- Site Admin
- Posts: 4915
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: Native Ultimate Plans
Seems like I could just scale up the one I drew, add a sub floor and drive well, and that would be it. Might have to add a skeg up front for track with those drive fins. Build would have to add a rudder.
-Matt. Designer.
-
- Posts: 129
- Joined: Mon Sep 10, 2007 10:15 pm
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: north Georgia, USA
Re: Native Ultimate Plans
If the drive was mounted in the tunnel, it would have to stick down enough so that the blades wouldn't hit the sides when they came up. That seems like it would mess up water flow through the tunnel.
-
- Site Admin
- Posts: 4915
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: Native Ultimate Plans
hmmm.... good point. Hadn't thought of that. Anyone get a look at the bottom of that thing? I see it has like a rear pontoon effect.
But does it start mid-hull or ...?
But does it start mid-hull or ...?
-Matt. Designer.
-
- Design Reviewer
- Posts: 1965
- Joined: Wed Jan 04, 2006 8:54 am
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: Queensland, Australia
- Contact:
Re: Native Ultimate Plans
Only guessing here, but I think there is a mid hull to house the drive assembly.
Regards,
Mick
JEMWATERCRAFT Swampgirl; Wadefish;Touring Pirogue;South Wind; P5 ;
Laker X 2, Sasquatch 16.5 T-V 15 Okwata 15:
Cobia 15 (under construction)
Mick
JEMWATERCRAFT Swampgirl; Wadefish;Touring Pirogue;South Wind; P5 ;
Laker X 2, Sasquatch 16.5 T-V 15 Okwata 15:
Cobia 15 (under construction)
-
- Posts: 129
- Joined: Mon Sep 10, 2007 10:15 pm
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: north Georgia, USA
Re: Native Ultimate Plans
Matt, watch this video it shows the bottom of the Hobie. http://www.youtube.com/watch?v=wbr9Q36KAgc
-
- Site Admin
- Posts: 4915
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: Native Ultimate Plans
That thing is a beast. I'd be willing to try and do something but it would require a full custom design fee with non-refundable deposit.
I've gotten hosed on these type projects before.
I've gotten hosed on these type projects before.
-Matt. Designer.
-
- Design Reviewer
- Posts: 1965
- Joined: Wed Jan 04, 2006 8:54 am
- Type of boat I like: <-- Please read instructions to the left and delete this text. Then, tell us what type boat you like! :-)
- Location: Queensland, Australia
- Contact:
Re: Native Ultimate Plans
Thanks for the link mate.
Too big, too heavy and too complex for my tastes but some very good ideas there.
I really like their new rudder set up and their front hatch.
Too big, too heavy and too complex for my tastes but some very good ideas there.
I really like their new rudder set up and their front hatch.
Regards,
Mick
JEMWATERCRAFT Swampgirl; Wadefish;Touring Pirogue;South Wind; P5 ;
Laker X 2, Sasquatch 16.5 T-V 15 Okwata 15:
Cobia 15 (under construction)
Mick
JEMWATERCRAFT Swampgirl; Wadefish;Touring Pirogue;South Wind; P5 ;
Laker X 2, Sasquatch 16.5 T-V 15 Okwata 15:
Cobia 15 (under construction)
-
- Site Admin
- Posts: 4915
- Joined: Fri Jun 18, 2004 8:14 pm
- Type of boat I like: Wooden
- Location: Greensboro, NC
- Contact:
Re: Native Ultimate Plans
It has some great ideas and features. But it starts getting too complicated for the amateur boat builder to design everything in to be built.
If I were to design something like that it would be tough to do the bottom. Look the video about 5:54. You can see the lower hull is almost like a regular hull bottom and then the pontoons start to form after the drive well area.
I bet a wide canoe or pea-pod style row boat with very fine entry would work nicely. Would have to add a little something on the stern to keep it from squatting when seated. It look like they designed it for optimum balance when standing, which is done forward of the seat.
I like the rod tubes, and rod handle storage area. That could be done real easy. The cutting board platform/storage right in front of the seat is neat and I like the replaceable mount mini deck things up front. That's a cool idea for not having to drill into the main hull to mount stuff. A builder could incorporate a couple nut plates into the hull to duplicated that removable platform.
But the biggest challenge would be the drive well. I haven't gotten enough feedback from Aloha Dan about it what I drew up for him worked. He mentioned some adjusted that had to be made.
If I were to design something like that it would be tough to do the bottom. Look the video about 5:54. You can see the lower hull is almost like a regular hull bottom and then the pontoons start to form after the drive well area.
I bet a wide canoe or pea-pod style row boat with very fine entry would work nicely. Would have to add a little something on the stern to keep it from squatting when seated. It look like they designed it for optimum balance when standing, which is done forward of the seat.
I like the rod tubes, and rod handle storage area. That could be done real easy. The cutting board platform/storage right in front of the seat is neat and I like the replaceable mount mini deck things up front. That's a cool idea for not having to drill into the main hull to mount stuff. A builder could incorporate a couple nut plates into the hull to duplicated that removable platform.
But the biggest challenge would be the drive well. I haven't gotten enough feedback from Aloha Dan about it what I drew up for him worked. He mentioned some adjusted that had to be made.
-Matt. Designer.